Loading...
pmt diesel performance header
Site Updated:
  Advanced Search
Items in the shopping cart:0
Current total:$0.00
Search:
pmt diesel performance header
pmt diesel performance header
home about us contact us basket checkout
| Log In / Register | | Click here to shop by manufacturer | Can't find what you're looking for? | Sitemap |
1-800-768-2447.

Diesel Performance

Shop By Product


MVP Authorized Dealer

diesel performance parts authorized dealer

sema member


Official PayPal Seal

Left menu space
Left space
 
MAG-HYTEC MAG-727-D Transmission Pan Dodge Ram



Transmission Pan
Dodge Ram
727 /518 / 47RE / 47RH / 48RE
1989-2007



Sku # : MAG-727-D
Our Price :
$237.50
Qty
:


Product Detail

36RH, 37RH - 66 to 89
46RH, 47RH - 89 to 95 and is also called the A-518
46RE, 47RE - 96 to 01
48RE

Every Mag-Hytec transmission pan comes fully assembled with everything you need to install it yourself.

  • Deep high-capacity sump for maximum cooling
  • Magnetic drain plug
  • 303 hardware except allen head cap screws are zinc plated
  • 1/8 NPT temperature sender port
  • Finned aircraft aluminum construction
  • Requires only three allen key wrenches (included) for installation and service
  • O-rings require no gaskets or sealants*

* 727 TorqueFliet models use Mag-Hytec hard paper gasket or it can be purchased at Transtar Ind. Inc.

Holds 1 quart more fluid than stock pan


INSTALLATION RECOMMENDATIONS

Please read these instructions and parts list completely before installing this new transmission pan. Consult your owner's or shop manual for transmission fluid requirements.

TOOLS REQUIRED

1/2 socket wrench and driver (for removing the old cover)
1/4 allen bit with a 3/8 ratchet drive (1/4 allen key is furnished)
3/16 allen bit with a 3/8 ratchet drive
3/8 drive torque wrench
Gasket scraper
Smooth flat file by 8 to 12 in. long
Oil drain pan (minimum 12 Qt. capacity)
ATF+3 type 7176, 2001 up ATF+4 or ("LE" 7500 Monolec Power Fluid for severe service and HD applications)


PARTS CONTENT

Number Quantity Item
1. 1 Mag-Hytec Transmission Pan with a Mag-Hytec Buna 70 gasket
2. 14 5/16-18 zinc plated allen head cap screws (Torque 12-16 ft. Ibis)
3. 16 5/16 stainless AN washers
4. 1 Drain plug assembly with magnet and O-ring ARP 568-910 (installed)
5. 1 1/8 pipe plug SS (for optional temperature sender not included) Drain plug and 1/8 pipe plug (Torque to 30 in. Ibs)

A word of caution to the installer / vehicle owner:

The Mag-Hytec pan is designed to fit the factory Dodge #727 transmission body as supplied as original equipment. However, in some applications, or because of the use of certain factory options and/or after market equipment, there may be clearance problems between your Mag-Hytec pan and other vehicle components. It is the responsibility of the vehicle owner and installer to ensure that there is no contact between the pan and other moving or fixed vehicle components. Contact with any vehicle component or the modifying of the Mag-Hytec pan voids the warranty. Mag-Hytec assumes no liability, expressed or implied, for damage or injury to persons or property.

Installation:

1. Park your vehicle on level ground and apply the parking brake. Use jack stands if the vehicle must be raised.
2. Position a large drain pan under the transmission to catch the fluid. Also drain the torque converter.
3. Starting at the rear, remove the 14 existing pan bolts.
4. Using a gasket scraper, start at the rear of the pan and carefully (so as not to gouge the transmission case) insert between the existing pan and transmission housing and pry the old pan off.
5. Allow all of the old oil to drain.
6. Using a gasket scraper, carefully remove all of the old gasket material (dried silicone) from the transmission case.
7. Use clean lint free rags to clean the transmission case gasket surface. The surface must be clean and flat for the gasket to seal.
8. Before installing the new Mag-Hytec pan, check the gasket matting surface on the transmission case for dents, irregularities, or gouges. Should any exist, carefully remove the high spots using a smooth flat file. BE CAREFUL NOT TO "ROUND OFF" THE FLAT GASKET SURFACE.
9. Remove the filter and replace it with a Dodge filter (Dodge Part #3515996up through '97, Part #52118789 for '98's and up. Mag-Hytec Buna 70 Gasket or Transtar Part #3859F gasket are both equivalent for all 727 bodies.
10. Apply a thin layer of ATF trans oil to the Mag-Hytec Drain plug O-ring.
11. Align the bolt holes and install the 14 cap screws and washers until they are installed "finger tight."
12. Using a 1/4 hex bit and 3/8 drive torque wrench, torque the zinc plated allen cap screws to (12-16 ft. lbs.) in a "cross tight" pattern.
13. Check the drain plug and 1/8 pipe plug for tightness. If you are going to install a temperature sender, do so at this time. Remove the 1/8 pipe plug and install the sender in its place. Be Sure To Use LPS All Purpose AntiĀ­Seize or equal On The Sender's Pipe Threads. "TIGHTEN" both the DRAIN PLUG and 1/8 PIPE PLUG TO (30 in. Ibs) DO NOT OVER TIGHTEN.
14.Remove the dipstick and add in the new ATF or ("LE" 7500 Monolec Power Fluid for severe and HD applications). The Mag-Hytec 727 -D ( Deep pan) holds 6.5 qts. of oil. 1.5 quarts of oil over a stock pan. Fill to full line on dipstick.

Maintenance:

The Mag-Hytec pan is constructed of high quality aircraft aluminum and has a powder-coated finish. The bolts are zinc plated allen head screws and the washers are stainless steel. These components require no maintenance.

We suggest you follow the manufacturer's recommendations for the transmission service intervals. You may drain your trany oil without removing the Mag-Hytec pan. However, we recommend you remove the pan and change the filter at every trany oil change. You may notice "fuzzy" metallic particles on the magnetic drain plug. This is normal wear. (If you notice any larger chips of metal on the magnetic portion of the plug, further inspection should be performed. We suggest that this inspection be performed by a professional mechanic who specializes in automatic transmissions.) Remember to clean the drain plug assembly prior to reinstallation. Apply a thin layer of oil to the drain plug a-ring and reinstall.

(3D in. Ibs) DO NOT OVER TIGHTEN. Follow the procedure for filling the transmission.

When it's time to service your transmission, DO NOT USE ANYTHING TO "PRY" THE PAN FROM THE TRANSMISSION CASE that will damage the gasket surface. If you do damage the surface, use a mill smooth file carefully.

Be the first to write a review.

  [Write Review]

No customer review found.

Recently Viewed Items




Transmission Pan
Dodge Ram
727 /518 / 47RE / 47RH / 48RE
1989-2007

$237.50

Social Bookmarking

Add to Google
Add to My Yahoo!
Add to MSN
Subscribe with Bloglines
Subscribe in NewsGator Online
Add to del.icio.us
Add to reddit
Add to LookSmart Furl
Add to Blogger
Add to Facebook
Add to BlinkList
Add to FeedMe
Add to Spurl
Add to Netscape
Add to Ask.com
Add to Live
Right right-line
| Custom Programming | ECU Locations | External Directory |

Copyright © 2017 Pmtdiesel.com. All rights reserved.
No part of this web site may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying or
recording or by any information storage and retrieval system, without written permission of Pmtdiesel.com.

PerformanceCartz.com - Custom Golf Carts of South Florida